PA66 103FHS NC010 DuPont nylon resins, DuPont Performance Polymers Product description: Non-reinforced polyamide resin 66NYLON DuPont Performance Polymers Product description: Non-reinforced, heat stabilized polyamide 66 PA66 DuPont distributor of professional-quality professional services agent original package fake a lose ten Unit Test Method Density heat stabilizer additive lubricant thermal stability lubricating release characteristics UL rating agency unrated form particle physical properties of injection molding processing methods Dry Conditioned 1.14 - g / cm3 ISO 1183 Shrinkage ISO 294-4 the flow direction 1.3 - 1.4% flow direction -% Water absorption ISO 62 73 ° F, 24 hr, 0.0787 in 8.5 -% balance, 73 ° F, 0.0787 in, 50% RH 2.6 -% viscosity 145-- Unit Test Method cm3 / g ISO 307 after adjusting the mechanical properties of dry tensile modulus 450000 203000 psi ISO 527-2 tensile stress (yield) 12300 7980 psi ISO 527-2 tensile strain (yield) 4.5 25% ISO 527-2 nominal tensile strain 20> 50% ISO 527-2 flexural modulus 406000 189000 psi ISO 178 film Dry Conditioned Unit Test Method Elongation - MD (yield) 4.5 - Strength ISO 179 / 1eA -22 ° F 2.1 1.4 ft · lb / in2 73 ° F 2.6 5.2 ft · lb / in2 simply supported% ISO 527-3 Impact Dry Conditioned Unit Test Method Charpy notched impact Beam unnotched impact strength ISO 179 / 1eU -22 ° F 170 ft · lb / in2 without breaking 73 ° F without break no break Notched Izod Impact Strength ISO 180 / 1A -40 ° F 2.6 - ft · lb / in2 -22 ° F 2.9 2.4 ft · lb / in2 73 ° F 2.6 5.2 ft · lb / in2 unnotched Izod impact strength ISO 180 / 1U -22 ° F 140 ft · lb / in2 without breaking 73 ° F 140 ft · lb Unit Test Method Heat Deflection Temperature / in2 dry thermal performance without breaking the adjusted 66 psi, without annealing 392 - ° F ISO 75-2 / B 264 psi, without annealing 158 - ° F ISO 75-2 / A glass transition temperature of 3 140 - ° F ISO 11357-2 melting temperature of 3 504 - ° F ISO 11357-3 ISO 11359-2 linear thermal expansion coefficient of the flow of 5.6E-5 - in / in / ° F transverse 6.1E-5 - - Unit Test Method volume resistivity in / in / ° F dry electrical performance after adjustment 1.0E + 14 1.0E + 11 ohm · cm IEC 60093 permittivity ASTM D150 100 Hz 3.40 - 1 kHz 3.40 - 1 MHz 3.20 - Dissipation Factor ASTM D150 100 Hz 1.0E-6 - 1 kHz 1.0E-6 - 1 MHz 2.0E-6 - compared to the anti-tracking index (CTI) (0.118 in) PLC 0 - UL 746 Tracking Index 600 - V IEC 60112 flammability Dry Conditioned Unit Test Method flammability rating IEC 60695-11-10, -20 0.0280 in V-2 - 0.0591 in V-2 - limiting oxygen Index 28 -% ISO 4589-2 dry mold filling analysis after adjustment units melt density 1.01 - g / cm3 Specific Heat Capacity of Melt 0.667 - Btu / lb / ° F Thermal Conductivity of Melt 1.1 - Btu · in / hr / ft2 / ° F supplementary information Dry Conditioned Units Effective Thermal Diffusivity 0.0500 - cSt